SpeedBox 3.0 for Brose

SpeedBox 3.0 for Brose

This tuning chip removes the 25 km/h speed limit of your Brose / Brose Specialized motor so that you can ride much faster with full motor support (not compatible with Specialized SL models). You even have the option of setting the maximum supported speed individually.

As this is the third generation SpeedBox chip, the e-bike display now even shows the correct speed.

You don't need a PC or smartphone to operate the SpeedBox.

Advantages of the SpeedBox 3.0 for Brose at a glance

-25 km/h speed limit is removed completely.

-Maximum speed can be set individually: You can set the level of maximum motor assistance by first switching the mode down three levels and then up three levels again (TURBO - TRAIL - ECO - OFF - ECO - TRAIL - TURBO). Then the current speed limit will be displayed. You can now set the maximum speed by briefly pressing the WALK button or by turning the rear wheel 360°. A displayed value of 1.5 km/h would correspond to 15 km/h, 4.0 km/h would be 40 km/h, and so on. The last value displayed is saved after 5 seconds of inactivity.

-Correct values in the e-bike display: Even when tuning is activated, the e-bike display shows correct values, e.g. current speed, average speed, range, daily distance, etc.

-Tuning can be switched on and off: You can conveniently control the tuning via the control buttons of your e-bike. Switch tuning on by pressing the WALK button. Then the display briefly shows 9.9 km/h to signal that the tuning has been switched on and the speed limit has been lifted. Press the WALK button again to turn the tuning off. A short display of 2.5 km/h then signals that the tuning has been cancelled and the maximum supported speed ends again at 25 km/h, just as usual. Your e-bike will then function as if no tuning chip had been installed. Tip: If your e-bike does not have a WALK button, you can also use the key combination + - + - to activate / deactivate the tuning.

-The SpeedBox 3.0 chip does not need its own battery.

Installation

The SpeedBox 3.0 is a chip or module that must be connected to the engine. This means that you have to gain access to the corresponding connections on the engine. Disconnect the cable connectors from the motor to the speed sensor and from the motor to the display. Then connect the SpeedBox to the appropriate connectors (see illustration). To simplify the installation, coloured connectors are used, which have been provided with a key for the correct connection. You can therefore install the module yourself.

If you want to restore the e-bike to its original condition at some point, you can remove the chip at any time.

Important notes:

-If you want to install the SpeedBox 3.0 in a brand new Brose e-bike, you must first ride the bike for at least 10 km before starting the chip for the first time.

-If you want to update the software of your e-bike, you must first uninstall the SpeedBox from the e-bike. Then update the software and reinstall the SpeedBox.

Tip: If you want your tuning with even more comfort and additional functions, you can also purchase the SpeedBox 3.0 for Brose in a "B.Tuning" version, which is compatible with the practical SpeedBox app. You will then benefit from practical additional features (motor lock, driving data analysis, etc.).

SpeedBox 3.0 for Brose - Compatibility

This tuning module is compatible with the following e-bike motors:

-Brose Specialized (NOT with Specialized SL - in this case please select the "SpeedBox 3.0 for Specialized")

-Brose S-MAG (NOT with Brose S Mag FIT)

-Brose S

-Brose T

-Brose T-ALU

-Brose C

-Not compatible with Brose Specialised SL models!

-Not compatible with Brose e-bikes with FIT system / not compatible with Brose S Mag FIT!

-Not compatible with e-bikes that do not have a connection on the display port (usually just a cap)

-Not compatible with Enviolo Automatiq

Tip: If you have a Specialized SL e-bike, please select the "SpeedBox 3.0 for Specialized".

-Not compatible with the SpeedBox app.