SpeedBox 1.2 Tuning for Bosch Smart System with rim magnet

SpeedBox 1.2 Tuning for Bosch Smart System with rim magnet

Attention: We strongly advise against downloading the new Bosch engine software update 11.13.0, as this can lead to incompatibilities with SpeedBox Tuning. Please note that the warranty for SpeedBox products does not cover malfunctions caused by updating the engine. So please do not install any Bosch updates!

Tuning chip for e-bikes with the latest 4th generation Bosch motors with Smart System and Bosch rim magnet.

The SpeedBox 1.2 for Bosch BES3 removes the speed limit of Bosch e-bikes with Smart System drive. This allows you to ride significantly faster than 25 km/h with full motor support (a maximum of 35 km/h is recommended).

This version of the SpeedBox is specially designed for Bosch Smart System e-bikes with a rim magnet. Corresponding models can be recognised by the magnet on the rear wheel valve.

Important: The "SpeedBox 1.2 Tuning for Bosch Gen4 Smart System (BES3) from 2022 with rim magnet" will be available from January 2024.

The tuning can be switched on and off using the WALK button.

Important: When tuning is active, the E-Bike display does not show the correct speed. However, the total distance is displayed correctly, but only after a "countdown" has elapsed at the end of the ride.

Our tip: If you would like to view the correct speed and all ride data during your ride, we recommend the "SpeedBox 1.2 B.Tuning" version, as this is also compatible with the practical SpeedBox app. You can use the app to view the real riding data on your smartphone display while on the move (suitable smartphone mounts for the handlebars are available in our shop).

Made in the Czech Republic.

How to use it

To activate all the functions of the SpeedBox correctly, it is necessary to enter the menu after the first switching on of the e-bike after the tuning installation and to switch to the circumference of the wheel of your e-bike.

Operating the tuning chip is simple. Tuning can be switched on by briefly pressing the WALK function (hold down the "-" button). To confirm, the display briefly shows the value 3.5 km/h (2.2 mph). Tuning is then active and the 25 km/h limit can be exceeded with motor support.

To switch off the tuning, simply press the WALK function again briefly (hold down the "-" button). The value 2.5 km/h (1.6 mph) is briefly shown on the display - this indicates that tuning has been deactivated; the speed limit is back to 25 km/h.

There are also e-bikes on which the WALK function is not available or active. In this case, the tuning can also be switched on and off by double switching between two modes, i.e. by pressing the - + - + button combination.

Setting the maximum speed

With the SpeedBox 1.2 you can set the level of maximum motor support individually. To do this, you must first change the modes as follows: TURBO - eMTB - TOUR+ - ECO - TOUR+ - eMTB - TURBO. The current speed limit is then displayed. You can now adjust the limit by briefly pressing the WALK function or turning the rear wheel 360°. A displayed speed of 2.5 km/h would correspond to a maximum speed of 25 km/h, 3.0 would be 30 km/h, 3.5 would correspond to 35 km/h, etc. The last displayed speed limit is saved after 15 seconds of inactivity.

Installation

SpeedBox 1.2 is a tuning chip that must be permanently connected to the e-bike. To simplify installation, original connectors are used in the production of the chip to ensure a correct connection.

Important:

Connect the plugs in the direction of the lock and do not rotate the connectors when plugging them in!

Important information

-A maximum speed of 35 km/h should not be exceeded.

-SpeedBox recommends not to update the software of the Bosch e-bike.

-Activation or deactivation of the tuning should always take place before the ride and not during the ride.

-Leave the E-Bike switched on for a while after the end of the ride until the SpeedBox has completed the "countdown" (indicated by the continuation of the ride time on the display until it stops and the correct ride distance is displayed) to avoid tuning detection by the Bosch software.

-If you want to install a SpeedBox 1.2 in a brand new e-bike, you must ride at least 10 km on this e-bike before you start the chip for the first time.

-During short breaks, you should keep one foot on the pedal so that the "countdown" deduction process does not start, so that you can continue riding seamlessly.

-During longer stops, you should allow at least a partial "countdown" (deduction of kilometres) to run through.

-Do not remove the display from the E-Bike until the "countdown" (deduction of kilometres) is complete.

Compatibility

The tuning chip is only compatible with Bosch Smart System e-bikes with rim magnets.

-Compatible with all motors and displays used with the Bosch Smart System.

Not compatible with:

-Bosch Smart System e-bikes with standard magnet (brake disc magnet spoke magnet).

-Bosch Smart System e-bikes with ABS system.