MBIQ-S Ebike Tuning for ANANDA mid-mounted motors

MBIQ-S Ebike Tuning for ANANDA mid-mounted motors

A microcontroller-based tuning tool for e-bikes with ANANDA mid-mounted motors that completely removes the 25 km/h speed limit. The tool comes as a ready-to-use sensor solution that simply needs to be exchanged for the existing speed sensor. As a result, you can ride much faster than before with full motor assistance.

The tuning can be activated / deactivated (programming) by means of certain wheel movements when raising the e-bike. Neither a PC nor a smartphone are needed to control the tuning.

In addition, the MBIQ-S is completely maintenance-free and does not require its own battery.

Thanks to the compactly integrated electronics, the tuning of the MBIQ-S takes place in the smallest installation space. Since a sensor similar to the original sensor is used, there are virtually no optical changes to the e-bike.

The electronics of the MBIQ-S are cast into the housing and thus protected from moisture.

How it works

After connection, the MBIQ-S will analyse the current speed profile, process it and - if tuning is active - output manipulated values. As a result, the preset 25 km/h speed limit can be exceeded - this enables much faster driving with full motor support.

Important note: Due to this special functional principle, the speed display is "frozen" at approx. 20 km/h on the display when driving >25 km/h (depending on the model). The same value is then always displayed at higher speeds. The total kilometres are then also lower for this range.

A speed halving, as known from some other tuning tools, does not take place with the MBIQ-S.

Programmable by the customer

With the MBIQ-S, three operating modes can be switched on, allowing the tuning to be switched on and off as required. Programming is done when the e-bike is switched on by certain wheel movements that move the magnet along the sensor. The set operating mode is indicated by the display of different speed values on the display. The following operating modes are available for selection:

Tuning permanently activated (the speed limit is permanently removed, from approx. 25 km/h the displayed speed is "frozen").

Tuning permanently deactivated (the speed limit is not lifted, engine support up to 25 km/h with real speed display).

Activation after switch-on condition: To switch on tuning, the magnet must be in front of the sensor for at least 4 seconds during start-up, otherwise tuning is deactivated. Here you can decide spontaneously when switching on whether the tuning should be active or not.

The operating instructions explain in detail how to set the various operating modes.

In a similar way, you can also set the limit value up to which speed the motor should be supported (setting the maximum support speed).

Installation

This Tuning Tool is a replacement sensor: This means that the existing original sensor of the e-bike has to be replaced with the MBIQ-S. The MBIQ-S can be installed in the same way as the Tuning Tool. Since the Tuning Tool is equipped with the same connectors, an optimal connection is ensured.

You will find the original sensor on the rear frame, where it works in conjunction with the magnet attached to the rear wheel.

Tip: When pulling out the original sensor, pull through a suitable pull wire along which you can thread the tuning tool.

Note: On some models the magnet is also positioned at the height of the mating axle. If this is the case, you will have to remove the rear wheel to install the tuning tool.

This requires a little technical skill. You will find more detailed information on installation in the installation instructions.

You can simply keep the original sensor in case you want to restore your e-bike to its original condition at some point.

MBIQ-S Ebike Tuning for ANANDA mid-mounted motors - Compatibility

ANANDA e-bike mid-mounted motors with the 3-pole connector shown above - e.g.:

-Ananda M80

-ANANDA AM80 Agile

-Ananda M81

-...

The tuning tool is compatible with the common motor firmwares of the manufacturers. The evaluation of the engine software is not affected by the manipulated values.

Please check the compatibility of the plug and the sensor in advance!

MBIQ-S Ebike Tuning for ANANDA mid-mounted motors - Technical data

Functional principle: speed manipulation (no halving).

Connection type: exchange sensor.

Connection length: approx. 25 cm.

Display: Manipulated values from approx. 22 km/h.

Tuning can be switched on and off (programmable).

Power supply: Not necessary, as the supply is passive via the sensor path.

Weight approx. 12 g.