MBIQ-P Plug-in solution AEG, Panasonic & Flyer (2pin)

MBIQ-P Plug-In Solution for AEG / Panasonic / Flyer (2pin)

The MBIQ-P is a microcontroller-based tuning tool that removes the 25 km/h speed limit of AEG / Panasonic / Flyer e-bike motors. There are no further functions. As it is a practical plug-in solution, installation is extremely simple: in principle, the MBIQ-P simply has to be plugged in between the speed sensor and the motor control unit.

The MBIQ-P is programmable by the customer so that the tuning can be switched on or off as required. An extra battery is not required, as the power supply is provided passively via the sensor path.

With this ingenious tuning tool, you can finally discover the full potential of your e-bike drive and ride much faster than 25 km/h with full motor support!

Functionality

After installation, the MBIQ-P analyses and processes the current speed profile and, if tuning is activated, passes on manipulated values. In doing so, speeds above 25 km/h are blocked for the motor firmware, which results in the 25 km/h speed limit being completely removed.

Important note: Due to this special mode of operation, the e-bike display will no longer show correct speed values from a speed of approx. 22 km/h onwards.

By the way, the evaluation of the motor software is not influenced by the manipulated values ("anti-tuning-ready").

Customer programmable

The MBIQ-P can be programmed, which allows the tuning to be switched on and off.

Programming is done by means of certain wheel movements when the e-bike is started up (PC or smartphone are not required). In this way, three different operating modes can be set:

-Mode 1: Tuning mode / tuning permanently activated (25 km/h speed limit is lifted, no correct speed display from approx. 22 km/h onwards).

-Mode 2: Normal operation / tuning permanently deactivated (engine support completely normal up to 25 km/h, correct speed display).

-Mode 3: Tuning selectable at start. In this mode, when the e-bike is switched on, you can use the magnet to determine whether the tuning should be active or not. To switch on the tuning, the magnet must be in front of the sensor for at least 4-5 seconds when starting up, otherwise the tuning remains inactive.

When correctly executed, the respective operating mode is indicated by the brief display of certain speed values on the display.

MBIQ-P for AEG / Panasonic / Flyer (2-pole) - Data at a glance

-Speed limitation is completely removed.

-The max. supported speed can be set in several steps to a desired value (from version v_I_1).

-Programmable by the customer (without additional devices).

-Tuning can thus be switched on and off.

-Mode of operation: Speed manipulation (no halving).

-Connection type: Plug-in solution, the tool is plugged in between the sensor and the motor.

-The MBIQ-P is very small and requires little installation space.

-Display: When tuning is active, manipulated values from approx. 22 km/h onwards.

-The tool is completely maintenance-free.

-No separate power supply/battery required.

-"Anti-Tuning Ready".

-Weight: only approx. 5g.

-Connection length: approx. 15 cm.

-Made in Germany.

MBIQ-P Plug-In Solution for AEG / Panasonic / Flyer (2pin) Compatibility

This tuning tool is compatible with E-Bikes with Panasonic / Flyer mid-mounted motors with compatible 2 pin connector system, e.g.:

-Panasonic (e.g. GX... / Ultimate)

-AEG / Bafang

Others with compatible plug connector.

For AEG / Bafang please check the sensor + connector for compatibility in advance!

The MBIQ-P is compatible with the common motor firmware of the respective manufacturers.

Note: On some AEG models (e.g. Graveller 7xxx) the sensor/motor connector is reversed. Please check this beforehand and contact us if in doubt.