sIMPLEk Stick ECOplus for Brose

sIMPLEk Stick ECOplus for Brose - Tuning for up to 20% more range!

The sIMPLEk Stick ECOplus is a completely new type of e-bike tuning tool: The stick does not remove the 25 km/h limit on motor assistance, but instead significantly increases the range (up to 20%). This tuning tool should therefore be the optimal solution for all e-bikers who like to go on really long tours.

How does the sIMPLEk Stick ECOplus work?

After installation, the sIMPLEk ECOplus Stick causes a phased reduction of the factory-integrated speed limit of the motor assistance.

More precisely, as soon as the built-in ECOplus Stick detects a constantly driven speed, the motor support is gradually switched off. If the speed falls below a certain value or a certain period of time is exceeded, the motor assistance is creepingly switched on again. This procedure results in up to 20 percent more range, as you have to exert a little more muscle power.

The 25 km/h limit for motor assistance remains completely untouched by the sIMPLEk Stick ECOplus.

By the way, you can decide for yourself where you want to attach the sIMPLEk Stick to the e-bike - the most practical attachment is probably directly to the handlebars.

Important note: The sIMPLEk Stick EcoPlus is supplied as a kit that you first have to assemble yourself. However, since there are only 4 components, namely the circuit board, USB connector, USB housing and connection cable, the assembly is quite simple. However, we would like to point out that the USB connector must be soldered to the board - so a soldering iron must be used here. After that, the board including the USB plug only has to be inserted into the enclosed USB housing, and the stick is already assembled.

sIMPLEk ECOplus Stick for Brose - Installation

For installation, the sIMPLEk stick must be connected to the motor and the sensor of the e-bike using an insulation displacement connector. To do this, first remove the crank and pull off the motor cover. Unplug the speed sensor. Then cut the speed sensor cable to connect the individual wires to the insulation displacement connector. Then insert the cable ends into the insulation displacement connector and secure the cables by pressing the insulation displacement connector closed (note the label on the insulation displacement connector for the correct polarity). Route the USB connection cable to the desired position of the sIMPLEk stick using the cable ties provided - we recommend positioning it directly on the handlebars.

The ECOplus mode is activated as soon as you plug in the sIMPLEk stick - the range of your e-bike is already significantly increased.

Even in ECOplus mode, you can still read the correct speed you are travelling at. Up to a speed of 10 km/h, the current speed is indicated 1:1. Above a speed of 10 km/h and when the motor assistance is disengaged, the real speed is shown via the second digit and (if available) the decimal place of the e-bike display. A distinction must therefore be made between displays with and without decimal places:

Display with decimal place

5.6 km/h on the display = 5.6 km/h in reality

10.0 km/h on the display = 10 km/h in reality

10.5 km/h on the display = 5 km/h in reality

13.5 km/h on the display = 35 km/h in reality

Display without decimal place

5 km/h on the display = 5 km/h in reality

11 km/h on the display = 11-20 km/h in reality

12 km/h on the display = 20-30 km/h in reality

13 km/h on the display = 30-40 km/h in reality

Note: To ensure that the actual current speed is still displayed for each wheel circumference even in the active ECOplus mode, a one-off calibration must be carried out the first time the device is used.

sIMPLEk Stick ECOplus for Brose - Compatibility

- E-bikes with Brose drives

The sIMPLEk Stick ECOplus is a quality product made in Germany.