JUM-Ped Vmax Remover for 2 BionX drives

JUM-Ped Vmax Remover for 2 BionX drives

With this tuning tool, the 25 km/h speed limit of the motor assistance of two e-bikes with BionX drive can be adjusted, allowing you to make the electric bikes much faster! Tuning is absolutely simple and straightforward with the JUM-Ped - there is no need to remove the motor or battery for installation. With the tuning tool, you can reset the speed lock of your BionX systems within a few seconds. You don't need a PC or any basic technical knowledge to do this.

Functions of the JUM-Ped-SE:

- Increase the level of maximum motor assistance to a value of your choice (maximum speed can be set individually).

- Select the maximum speed of the throttle function.

- Set mileage, count charging cycles,....

Procedure: First remove the shrink tubing from the original connectors near the console on the handlebars. Then you have to disconnect the plug on the e-bike and connect the JUM-Ped SE tuning device to the plugs of the bike. Now all you have to do is switch on the tool and you can start tuning! By the way, the JUM-Ped-SE tool does not remain on the bike after tuning. The tuning tool has an LCD display with a choice of German or English. It is operated intuitively and conveniently via 4 buttons that allow you to select the desired speed from the menu or to enter an individual value (the maximum speed that can actually be achieved depends, among other things, on the performance of the used system).

The BionX motors are considered particularly efficient and powerful. The special feature of the BionX systems is that they support the rider proportionally to their pedalling force. In addition, the synchronous motor of the BionX system can also be used as a generator when riding downhill and braking, which extends the range by 7-15%. Tuning with the JUM-Ped-SE Vmax Remover for BionX can be done in just a few minutes: Simply connect the tuning tool between the console and the battery and the top speed of the BionX system can be increased by pressing a button. Afterwards, simply remove the tuning tool again (the tool itself does not remain on the e-bike). Of course, the tuning can be reversed at any time in the same way. Please note that this JUM-Ped-SE Vmax Remover BionX Tool is limited to a maximum of two vehicles or e-bikes - but you can make as many changes to them as you like with the tool. After the BionX tuning tool has been activated, the respective e-bike may no longer be used in street traffic. Riding after resetting the settings is at your own risk. Please observe the applicable legal regulations in your country.

Scope of delivery:

In addition to the JUM-Ped-SE Tuning Tool, the scope of delivery also includes all necessary connection cables, plugs and an instruction manual as a download. This JUM-Ped-Se is for the activation of 2 Bionx systems.

With which models does the JUM-Ped-SE Vmax Remover tuning tool work?

All e-bikes or pedelecs with BionX drive from June 2009 onwards with CanBus system (all firmware versions, all console types such as G1 / G2 / Ride / Ride+).

Notes for Smart and Grace e-bikes:

- Connect the JUM-Ped to the Smart or Grace bike as described.

- Select the desired value and confirm with the OK button.

- Immediately start pressing the buttons on the bike's console alternately (order is not relevant) - press the buttons only briefly, do not hold them.

- If you do this, the bike will not switch off and you can complete the unlocking with the JUM-Ped without any problems.

Notes on Diamant and Trek e-bikes:

A battery-powered version of the JUM-Ped is available for Diamant and Trek e-bikes, which works independently of the bike's power supply. The battery-powered version can only be ordered as a single version.

Important: This JUM-Ped for BionX for 2 drives is limited to 2 systems. This means: Once the JUM-Ped for BionX is connected to 2 specific BionX systems, the tuning tool cannot be used on any other BionX system anymore - it remains connected to the respective BionX systems forever. When the JUM-Ped for BionX is used for the first time, the configuration values and the serial number of the connected BionX system are saved in the tuning tool - this ensures that the original state of the BionX e-bike can be restored at any time if necessary. The product is excluded from exchange as soon as the seal on the packaging has been opened and the product has been connected to the motor.