MBIQ-CC 2 Universal for mid-mounted motors

MBIQ-CC 2 E-Bike Tuning Universal for mid-mounted motors, programmable, externally switchable

The MBIQ-CC 2 tuning tool is a microcontroller-based universal solution that is compatible with various e-bike motors with 2- or 3-wire speed sensors and push-in clamping technology. This tool completely removes the 25 km/h speed limit of the e-bike drives, so you can ride much faster with full motor support. In contrast to the conventional MBIQ-CC, the MBIQ-CC 2 offers the additional option of switching the tuning on and off by light signal (only with 2-wire sensors) or via an external switch (not included in the scope of delivery).

Important note: The MBIQ-CC 2 has the effect that (when tuning is activated) speeds above 25 km/h are blocked for the engine firmware - this removes the 25 km/h limitation. As a result, the displayed speed always remains ≤ 25 km/h - even if you are actually riding at a higher speed.

For installation, the MBIQ-CC 2 basically only has to be integrated into the existing sensor line. The process is simple, as the cables can simply be inserted into the push-in terminal. Soldering or press-fitting is not necessary.

The MIQ-CC 2 is maintenance-free and does not need its own battery (power is supplied via the sensor cable).

MBIQ-CC 2 (Universal) - Advantages at a glance:

- Removal of the 25 km/h speed limit.

- Universal solution for many e-bike drives with 2- or 3-wire sensors.

- Anti Tuning" ready.

- Programmable by the customer (without additional devices such as PC or smartphone).

- Externally switchable: can be switched on and off via switch or light signal (4-12 V DC).

- Easy installation thanks to push-in terminal.

- Completely maintenance-free.

- No extra power supply necessary.

- Compact and light (approx. 9 g).

Programmable by the customer

With the MBIQ-CC 2 you have the option of setting different operating modes by means of certain wheel movements when switching on the e-bike:

-Tuning permanently activated (speed limit removed, from a speed of approx. 25 km/h the display no longer shows the correct speed). You can deactivate tuning using the switch.

-Tuning permanently deactivated (e-bike runs as normal with correct speed display, motor support ends at 25 km/h).

-Tuning according to switch-on condition: In this mode, you can determine yourself whether the tuning should be active or not when you switch on the e-bike. You can determine this via the light signal. Alternatively, the tuning can also be switched on by placing the magnet in front of the sensor for approx. 3-4 seconds when the bike is started up. If this does not happen, the tuning remains inactive.

Please note:

On/Off via external switch: The switch is not included in the scope of delivery.

On/Off via light connection: Only with 2-wire sensors / 4-12V.

Light control is not possible with 3-wire sensors.

Simple installation

Your e-bike has a sensor that receives impulses per wheel rotation by means of a magnet for the purpose of determining speed. The magnet is located either on a rear wheel spoke or alternatively on the brake disc.

As already mentioned, the MBIQ-CC 2 is easy to install, as you basically only have to integrate the tool into the sensor cable of the e-bike, which is absolutely no problem thanks to the "Push In" clamp.

Proceed as follows:

First remove the battery before installation.

Gain access to the sensor plug and carefully pull it off the control unit.

Then insert the MBIQ-CC 2 into the line between the plug and the sensor using the push-in clamp. Please note that you have to cut the sensor cable for this.

If necessary, you can now also connect the lines to the light signal or to the external switch - this gives you the option of switching the tuning on and off in addition to the programmed operating mode.

The MBIQ-CC 2 is extremely compact and can therefore be installed in a space-saving manner.

MBIQ-CC 2 E-Bike Tuning Universal for mid-mounted motors - Compatibility

The MBIQ-CC 2 is compatible with numerous popular e-bike mid-mounted motors with 2- or 3-wire speed sensors:

Bosch (e.g. Active, Performance, CX, also Gen4 model year 2020/2021). Not compatible with Bosch Smart System 2022 (BES3).

Shimano Steps (e.g. E6xxx, E7xxx, E8xxx, EP8,...)

Panasonic (e.g. GX0, GX Ultimate,...)

Brose (e.g. Brose Drive-...)

Yamaha (e.g. PW-...)

AEG (e.g. ComfortDrive, SportsDrive, ...)

BH (e.g. BH 1E)

The MBIQ-CC 2 is "anti-tuning" ready and compatible with all common engine firmwares of the respective manufacturers.

Important note:

The external switch with which the MBIQ-CC 2 can be alternatively activated / deactivated is not included in the scope of delivery.