MBIQ-P for Brose / Specialized (Levo)

MBIQ-P for Brose / Specialized (Levo)

The MBIQ-P is a microcontroller-based tuning module for removing the 25 km/h speed limit on various Specialized e-bikes. The tool is a plug-in solution that must be inserted between the motor and speed sensor. Unlocking the e-bikes enables significantly faster riding with full motor support.

Tuning can be switched on and off by means of certain wheel movements when the e-bike is being started up. The level of maximum motor support can also be set. Neither a PC nor a smartphone is required to control the module.

When tuning is active, the e-bike display no longer shows the correct speed from approx. 22 km/h (manipulated values).

The MBIQ-P does not require its own battery, as the power is supplied by the e-bike.

The module is also completely maintenance-free. The electronics are safely moulded into the module housing so that no moisture can penetrate (IPX4 in accordance with EN 60529).

Programmable

With the MBIQ-P, the tuning can be programmed to a certain extent so that the tuning can be switched on and off as required. Programming is carried out by means of certain wheel movements when the e-bike is started up, during which the spoke magnet must be moved past the sensor.

The following modes can be set:

Mode 1: Tuning permanently activated (factory setting): The 25 km/h speed limit is completely cancelled. No correct speed display from approx. 20-22 km/h onwards.

Mode 2: Tuning permanently deactivated: Speed limitation to 25 km/h. The e-bike functions as if no tuning was installed (correct speed display).

Mode 3: Activation according to switch-on condition: Here you can decide when switching on the e-bike whether the tuning should be active or not. To activate the tuning, the magnet must be in front of the sensor for at least 4 seconds while the bike is being switched on. This is also achieved by means of certain wheel movements.

The maximum assisted top speed (Vmax) can also be set in a similar way.

Note: Programming is not absolutely necessary, as the module is delivered in ‘Tuning permanently activated’ mode (with the highest support level).

More detailed information on programming can be found in the enclosed operating instructions.

Installation

The MBIQ-P tuning module must be plugged between the existing sensor cable and the motor (integration into the current path of the existing speed sensor). To gain access to the plug connection, the motor cover must be removed briefly. In many cases, a pedal crank must also be removed.

In most cases, the module can be stowed in the connection area of the motor. It can also be stored in the frame tube, but this usually requires the motor to be detached from the frame.

After installation, the tuning module is not visible from the outside.

If necessary, the tuning can be removed again and the original condition of the e-bike is restored.

Tools required (not included in the scope of delivery):

-Cross-head screwdriver

-Hot air dryer (for the heat-shrink tubing)

Depending on the motor cover, a Torx or another Allen key may also be required.

If the pedal crank needs to be removed, a suitable crank puller is required.

Mode of operation

The MBIQ-P is a tuning module that works on the principle of speed manipulation (no halving). It processes the current speed profile and passes on manipulated values, eliminating the 25 km/h limit. There is no direct intervention in the communication of the system.

MBIQ-P for Brose / Specialised (Levo) - Compatibility

This MBIQ-S tuning tool is compatible with various Specialized (Levo) mid-drive motors - it should be noted that Specialized drives are based on motors from the German manufacturer Brose, but have been equipped with their own Specialized software.

Compatible e-bike drives:

-Brose Drive (S) / Specialised 1.2

-Brose Drive S / Specialised 1.3

-Brose Drive S MAG / Specialised 2.1

The MBIQ-P works independently of the e-bike display used.

Compatible with all standard motor firmwares from the manufacturer.

Information on the MBIQ-P module

Housing dimensions: approx. 2.5 cm x 1 cm x 1 cm

Weight of the MBIQ-P: approx. 5 g

Connection length: approx. 8 cm